
Fence cost by type: what each option asks of the budget
The fence type decides how much sits below ground, how much masonry is involved and how heavy the infill is. This page compares the cost drivers of each type we build, without pretending there is one rate for each.
Cost by fence type describes how the construction of each kind of fence – chain link, rigid mesh panels, game fencing, block walls, slats, composite or timber, and precast concrete panels – shifts the balance between groundwork, structure and infill in a quote.
What drives the cost of chain link and game fencing?
In short: light infill on posts, so most of the cost sits in posts, footings, tensioning and the length of the run.
Chain link (malla de simple torsión) and knotted game or livestock fencing are light fences on posts. There is no wall and the mesh itself is quick to hang, so the posts, their footings, the bracing at ends and corners, and the straining wires carry much of the cost. On long rural runs, clearing the line and dealing with uneven ground often matter more than the mesh.
These fences suit plots, fincas and land where a secure but open boundary is enough. For type-specific detail see mallatorsionmalaga.eu for chain link and mallacinegeticamalaga.eu for game and livestock fencing. How length affects the rate is explained on our fence cost per metre page.

Where does the money go in a rigid mesh panel fence?
In short: posts, footings and the panels themselves, plus a base or plinth if you choose one.
Rigid welded mesh panels, in 2D or 3D profiles, are heavier than chain link and are fixed to posts with clips. Each post needs a footing, and many owners add a concrete plinth or precast base along the bottom to stop digging and give a cleaner line. That base is a separate line and can noticeably change the total.
This type is common around homes, warehouses and plots where security and visibility both matter. More detail is on vallapanelrigidomalaga.eu.

Why do block walls and precast panels weigh more in a quote?
In short: they need continuous footings, masonry or heavy panels, and often render or a finish, so groundwork and structure dominate.
A block wall is built on a strip footing, course by course, with pillars at intervals and usually render or a decorative block face. A precast concrete panel fence slots heavy panels between posts, often on a block base. In both cases the footing and the structure are the main costs, and the finish adds another layer.
The reward is a solid, fully private boundary. Remember that a boundary wall is not a retaining wall; if it holds back soil, a technician has to assess it. See murosdebloquemalaga.eu for walls and precast panels.

What about aluminium slats, steel sheet, composite and timber?
In short: these are usually fitted between pillars or on a low wall, so the cost combines a masonry base with the infill system you choose.
Slatted fences in aluminium or steel, profiled steel sheet, composite boards and timber slats are mostly chosen for privacy and appearance. They are rarely free-standing on light posts; they sit between rendered or split-face pillars or on a murete. The quote therefore combines the masonry lines with the infill lines, and the infill's own cost depends on the profile, finish and how the boards are fixed.
Composite and timber bring their own considerations, such as expansion gaps and care. See vallasaluminiomalaga.eu for aluminium and steel, and vallascompositemalaga.eu for composite and timber.

How should cost influence the choice of type?
In short: decide what the fence must do first, then compare the cost of the types that meet that need.
Comparing a chain link run with a rendered wall on cost alone makes little sense; they solve different problems. Start with the purpose: privacy, keeping dogs in, security, marking a boundary or matching urbanisation rules. Then compare the types that meet it, ideally priced in the same quote so the groundwork lines are directly comparable.
Our post on lowering fence cost without cutting quality suggests ways to adjust scope sensibly, and first fence in Spain: the options is a good starting point if this is new to you. The factors behind each line are on the fence cost factors page.
How we build it – step by step
- Clarify the purpose
Privacy, security, pets, boundary marking or appearance – this narrows the realistic types.
- Check local rules
Ask the ayuntamiento and, where relevant, your urbanisation about allowed heights, materials and finishes.
- Send photos and length
We see the line, the ground and the access and can suggest which types suit the plot.
- Price comparable options
If you are torn between two types, we price both in the same quote so the shared lines match.
- Choose and confirm
You pick the option; we confirm height, finish and any low wall in writing.
- Build
We set out, lay the foundations, build any wall, fix posts or pillars and mount the infill, then clean up and hand over.
When is it the right choice – and when not?
A good fit if…
- Owners deciding between two or three fence types
- Comunidades comparing options for a shared boundary
- Budget planning before choosing materials
- Seeing how a low wall changes each option
Consider another option if…
- Choosing a type on cost alone without defining its purpose
- Comparing types priced by different contractors with different scopes
- Fences that would act as retaining walls
What affects the cost?
We don't publish fixed prices: every fence is quoted line by line using these factors.
- Fence type and infill system
- Need for a low wall or plinth
- Foundations: individual footings or continuous strip
- Render or decorative finish on masonry
- Pillar spacing and type
- Height
- Linear metres
- Ground, slope and access
- Removal of an old fence and clearing
Articles and guides
Fence cost factors: what raises or lowers your quote
Every fence quote is built from the same handful of variables. Once you know them, you can read any quote with confidence and see which choices are yours to make.
View details →
Your first fence in Spain: the options and what drives their cost
If you have just bought a property in Málaga province, the fence may be one of the first jobs on the list. The options, the vocabulary and the rules are probably new to you. This is a calm overview to start from.
View details →
How to lower the cost of a fence without cutting quality
When a quote comes in above budget, the temptation is to look for a lower price elsewhere. Often the better route is to adjust what is being built. These are the options worth comparing, and the ones to avoid.
View details →Frequently asked questions
Which fence type is the cheapest?
There is no single answer because the plot changes the picture. Light fences on posts usually involve less groundwork than walls, but a difficult site can change that. We price the options that fit your purpose.
Is a block wall always more expensive than a mesh fence?
A wall usually involves more groundwork and masonry, so it tends to weigh more in a quote for the same length. The exact difference depends on height, finish and the site.
Does a concrete plinth under mesh panels add much?
It adds a separate line for the plinth or precast base and its installation. Many owners choose it because it stops digging and gives a cleaner finish.
Are aluminium slats priced per metre?
The infill is often priced per metre or per panel, and the pillars and wall below as separate lines. Ask any quote to show both.
Do composite boards cost more than timber?
It depends on the specific products and the fixing system. We price the options you are considering side by side rather than generalising.
Can I mix types along one boundary?
Yes. For example, a wall with slats facing the road and mesh panels along the back. Each section is priced separately in the quote.
Which type is best for dogs?
It depends on the dog and the plot, but a solid base that stops digging helps. The network's dog-proof fencing page covers this.
Do you build gates for these fences?
Gates and automation are not part of our offer. Tell us where a gate will go so pillars and the fence line can be planned around it.
Does a wind-exposed site change the cost by type?
Solid fences catch more wind than open mesh, so posts and footings may need to be stronger. We take exposure into account when we assess the site.
Is painting or render included for block walls?
Only if the quote says so. Render, paint or a decorative face should appear as their own lines.
Can you price two types in one quote?
Yes, as separate options. That is the fairest way to compare, because the shared lines like setting out and access are identical.
Get an itemised quote for your fence
Send photos and the approximate length by WhatsApp or e-mail. We price every stage line by line, without commitment.